DeepSeek-V3 TPS calculator
Each card below is assessed against this model at the context length and minimum quality you choose. Speed is an estimate for a single request, calculated from the card's memory bandwidth and the size of the model once compressed.
Calculated for this model
818 cards we hold specifications for
Which GPUs can run DeepSeek-V3?
Set the inputs, read the answer
A longer conversation needs more memory, which can push this model off smaller cards.
Hides cards that would only fit the model by compressing it below this point.
0 cards match
Calculating| Needs | Quantisation | Fit | |||||
|---|---|---|---|---|---|---|---|
|
No card in our catalogue can run this model with these settings. |
|||||||
Speeds are estimates for a single request — one conversation at a time — calculated from memory bandwidth, model size and quantisation. Real throughput varies with the inference runtime and its version. Figures published by hardware vendors measure many simultaneous requests and are much higher.
On record
Full specification
Everything on record for this model. Most of it describes how it was trained rather than how it runs — useful context for judging how much work went into it, and how it compares with models built at a different scale.
Origin
Who built this model, where, and when it was published.
- Organisation
- DeepSeek
- Organisation type
- Industry
- Country
- China
- Published
- 24 December 2024
- Authors
- DeepSeek-AI, Aixin Liu, Bei Feng, Bing Xue, Bingxuan Wang, Bochao Wu, Chengda Lu, Chenggang Zhao, Chengqi Deng, Chenyu Zhang, Chong Ruan, Damai Dai, Daya Guo, Dejian Yang, Deli Chen, Dongjie Ji, Erhang Li, Fangyun Lin, Fucong Dai, Fuli Luo, Guangbo Hao, Guanting Chen, Guowei Li, H. Zhang, Han Bao, Hanwei Xu, Haocheng Wang, Haowei Zhang, Honghui Ding, Huajian Xin, Huazuo Gao, Hui Li, Hui Qu, J.L. C…
What it does
The problem areas the model was built for. A model can carry several of each.
- Domain
- Language
- Task
- Language modeling/generation, Code generation, Quantitative reasoning, Question answering
- Numerical format
- FP8
Size
How large the model is and how much data it was trained on. Parameters are the figure that decides whether it fits on a given graphics card.
- Parameters
- 671B
- Training data
- 14,800,000,000,000 tokens
- Batch size
- 62,914,560
Mixture-of-Experts (MoE) language model with 671B total parameters with 37B activated for each token.
"We pre-train DeepSeek-V3 on 14.8 trillion diverse and high-quality tokens, followed by Supervised Fine-Tuning and Reinforcement Learning stages to fully harness its capabilities"
15360 * 4096
Training compute
The arithmetic performed to train the model, measured in floating-point operations. It is a measure of what the training run cost, not of how fast the finished model answers you.
- Training compute
- 3.3 × 10²⁴ FLOP
- How it was established
- Operation counting,Hardware
6 × 37B × 14.8T = 3.29e24 pretraining FLOPs, 1e22 posttrainining FLOPs - see doc below https://docs.google.com/document/d/1C4zBvHh4UNnzaorwQSdG61zQJsBV9X3i3A70NeelxHY/edit?usp=sharing
The training run
What it physically took to train: which chips, how many, for how long, and what that drew from the wall.
- Training hardware
- NVIDIA H800 SXM5
- Chips used
- 2,048
- Chip-hours
- 2,788,000
- Hardware utilisation
- MFU 19.5%
- Power draw
- 2.8 MW
- Compute cost
- $5,390,000
- Data centre
- Paper on DeepSeek-V3
Table 4: Training metric comparison "Causal MFU only takes into account the flops of the lower triangle of the attention matrix (in line with FlashAttention), while non-causal MFU includes the flops of the whole attention matrix (in line with Megatron)" TFLOPS (causal) = 385 H800 maximum FP8 performance = 1979 TFLOPS therefore MFU = 385/1979 = 0.1947
Availability
Whether you can obtain the model and run it on your own hardware, which is what decides if any of the graphics-card figures on this page apply.
- Weights
- Open — downloadable
- Model access
- Open weights (restricted use)
- Training code
- Unreleased
- Hugging Face
- deepseek-ai
MIT and deepseek license https://github.com/deepseek-ai/DeepSeek-V3?tab=readme-ov-file I cannot see training code in this repo https://github.com/deepseek-ai/DeepSeek-V3?tab=readme-ov-file
How it is classified
Labels the source dataset applies when tracking notable models, and how confident it is in the entry.
- Likely above 10²³ FLOP
- Yes
- Why it is tracked
- Training cost
- Record confidence
- Confident
training cost was $5.3million USD (Table 1)
Sources
Where this record came from and when it was last checked.
- Reference
- DeepSeek-V3 Technical Report
- Last updated
- 19 February 2026
What the numbers mean
What it takes to run this model
At 671B parameters, DeepSeek-V3 is beyond what any single graphics card holds. Running it means either splitting it across several cards or renting hardware built for the job — 0 of the cards we track can hold it on their own, and all of them are datacentre parts.
Where it came from
DeepSeek-V3 was published by DeepSeek, in China, in December 2024. It comes out of industry.
It works in Language, and is recorded as doing language modeling/generation, Code generation, Quantitative reasoning, Question answering.
The weights being open is what puts this page in the calculator rather than only in the catalogue: it is a model you can actually hold. It is published under the deepseek-ai organisation on Hugging Face.
How it was trained
Producing it required around 3.3 × 10²⁴ FLOP of arithmetic, on NVIDIA H800 SXM5, which is a statement about the training budget rather than about inference.
Around 14,800,000,000,000 tokens went into training it.
Its inclusion criterion is training cost.
Step by step
How to choose a GPU for DeepSeek-V3
The table above has already assessed every card we hold specifications for against this model. Getting to your answer takes six steps.
-
01
Check what it needs before anything else
Every card here has been checked against DeepSeek-V3. Capacity is the gate — a card either holds it or it does not.
-
02
Match the context to your actual use
Set the context to what you will actually use. The cache grows with the conversation, and it is the usual reason DeepSeek-V3 stops fitting a card that seemed fine.
-
03
Choose how far you will compress it
Each card runs the least-compressed copy it can hold. Setting a floor drops the cards that only manage DeepSeek-V3 by squeezing it further than you would want.
-
04
Rank by throughput rather than spec sheet
Sort by speed to see how cards rank for DeepSeek-V3. It will not match a gaming ordering — generation is bound by memory bandwidth.
-
05
Check the fit verdict before buying
Tight means DeepSeek-V3 loads and works, with no room to raise the context later. Comfortable means you can. The difference matters more than a few tokens per second.
-
06
See what else that card runs
Following a card through to its own page shows every other model it can hold, which is the question that follows once DeepSeek-V3 is settled.
Answers
DeepSeek-V3 — common questions
Who created DeepSeek-V3?
DeepSeek-V3 was published by DeepSeek, based in China, categorised as industry.
When was DeepSeek-V3 released?
DeepSeek-V3 was published in December 2024. Capability per parameter has improved considerably since, so a newer model of the same size is often the better use of the same hardware.
What is DeepSeek-V3 used for?
DeepSeek-V3 works in Language, and is recorded as handling language modeling/generation, Code generation, Quantitative reasoning, Question answering. A model can carry several of each, so these are the areas it was built for rather than a limit on what it will attempt.
Where can I download DeepSeek-V3?
Its weights are published under the deepseek-ai organisation on Hugging Face. We do not host model files — this site calculates what hardware is needed to run them.
How much compute was used to train DeepSeek-V3?
Around 3.3 × 10²⁴ FLOP, on NVIDIA H800 SXM5. That measures what producing the model cost and says nothing about how quickly it answers once trained — inference speed comes from memory bandwidth, not from the training budget.
Can I run DeepSeek-V3 if it does not fit in my GPU?
Only by offloading, which is usually a false economy: the part in system memory drags the whole thing down — the nearest miss we calculate is short by 147.5 GB. Our figures for DeepSeek-V3 assume it is fully resident.
Would two GPUs run DeepSeek-V3 faster?
Capacity adds across cards; throughput does not. Since 0 of the cards we track already hold DeepSeek-V3 on their own, a second card is rarely the answer here.
Why does the quantisation differ between cards for DeepSeek-V3?
Each card is shown running the least-compressed copy it can hold, and DeepSeek-V3 appears at 1 different compression levels across the cards that fit it. Bigger cards get the more accurate version.
How accurate are these DeepSeek-V3 speed estimates?
Every figure is derived from memory bandwidth and model size, not benchmarked. That is why each is published as a range such as the range beneath each figure rather than a single number.
Is DeepSeek-V3 open source?
Its weights are published, so DeepSeek-V3 can be downloaded and run on your own hardware. Note that open weights is not the same as open source in the full sense — it says nothing about the training data, the training code, or the commercial terms attached.
How many parameters does DeepSeek-V3 have?
DeepSeek-V3 has 671B parameters. Mixture-of-Experts (MoE) language model with 671B total parameters with 37B activated for each token. That figure is the total, and it is what decides how much memory the model needs — roughly half a gigabyte per billion at the compression most people use.
The other direction
Looking at it from the other side?
This page starts from the model. If you already own a card and want to know everything it will run, start from the hardware instead.